ACV 611320-22-1

Item No. 611320-22-1
ACV 611320-22-1
Facia plate 1-DIN and HU Adapter kit SWC Audi Audi A1 (8X) 2010 - 2018 Colour: black vehicles with Chorus OEM HU with monochrome display vehicles without OEM HU 2 x SD vehicles without OEM Sat Nav vehicles without BOSE OEM amplified system connector: 40 Pin Quadlock VAG
price per Each
incl. tax
Pre-Order
Each
ACV 611320-22-1

ACV 611320-22-1

Item No. 611320-22-1
Facia plate 1-DIN and HU Adapter kit SWC Audi Audi A1 (8X) 2010 - 2018 Colour: black vehicles with Chorus OEM HU with monochrome display vehicles without OEM HU 2 x SD vehicles without OEM Sat Nav vehicles without BOSE OEM amplified system connector: 40 Pin Quadlock VAG
price per Each
incl. tax
Pre-Order
Each

Specifications

Description
ACV 611320-22-1
Category
FULL FITTING KIT SD
Description2
1-DIN Kit Audi A1(8X) 2010-2018 SWC/antenna

 CAN Bus
 
 connector: 40 Pin Quadlock VAG
 connector: OEM SWC > 3,5mm Jack / loose wire
 connector: OEM antenna Fakra(m/Set) > DIN(m)
 
 blue: +12V antenna remote
 blue: +12V amplified system remote
 
 vehicles with Chorus OEM HU with monochrome display
 
 vehicles without OEM HU 2 x SD
 vehicles without OEM Sat Nav
 vehicles without BOSE OEM amplified system
 
 dip switch settings for the retrofit device manufacturer (look into the manual)
 
 Vehicle application:
 
 Audi A1 (8X) 2010 - 2018
 
 Colour: black
 
 Following signals are provided:
 
 Reimported vehicles or vehicles with different software may be incompatible in functions.
 
 red: +12V ignition clamp 15
 orange: +12V illumination clamp 58
 purple/white: +12V reverse gear signal
 pink: speed pulse signal
 green: GND park brake signal
 
 load capacity outputs: 250 mA max.
 
 current requirement more than 250 mA:
 1 relay coil resistance 75 Ohm min.
 2 relays coil resistance 150 Ohm min.
 
 SWC
 
 Scope of delivery:
 
 1-DIN facia plate with pocket Audi A1 07/2010-04/2018 bulk > item: 281320-22-0
 SWC Audi A3/A4/A6/R8/TT Quadlock Multilead Amp >RCA bulk > item: 42xad002-0
 Antenna adapter Fakra(m)(set)>DIN(m) 12V phantom LEONI bulk > item: 1524-70-1-0
 
 General installation instructions:
 
 Verification:
 1: Check all operating functions and vehicle setting functions of the OEM HU.
 2: Disconnect the OEM HU voltage-free.
 3: Check all interface connections for correctness voltage-free.
 
 Connection and connection sequence:
 1: Check settings and hardware configuration of the interface voltage-free.
 2: Check configuration of the HU connection cable voltage-free.
 3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
 4: Connect all other connections according to the operating instructions of the retrofit HU.
 5: Connect the entire installation to the vehicle with the main connection last.
 6: Software configuration of the interface according to the instructions in the item text and in the manual.
 7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
 8: Function test of steering wheel remote control and vehicle
 
 Changes to the configuration of the interface and the HU connection cable:
 1: Change configuration voltage-free
 2: Reconnection see above 5 to 8
 
 In case of malfunction of the interface or the vehicle:
 1: Reinstall the OEM HU
 2: Operate the OEM HU
 3: Establish CAN bus shut down
 4: Check the hardware configuration of the interface
 5: Reconnection after CAN Bus shut down see above 5 and 6
 
 More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.
 
 More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
 1: Connections and changes are to be carried out exclusively by trained specialist installer.
 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
 3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection.
 4: Connections and modifications are made on the user's own responsibility without guarantee of function.
 5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
 6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.