ACV 611320-30-4

Item No. 611320-30-4
ACV 611320-30-4
Facia plate 2-DIN with pocket and HU connector kit i-dapter Skoda / VW Skoda Octavia (1Z) 01/2009 - 03/2013* Skoda Rapid (NH) 10/2012 - 04/2015** Skoda Rapid (NH) 04/2015 - 05/2017** Skoda Rapid (NH) 05/2017 - 02/2019** Skoda Roomster (5J) 06/2010 - 02/2015 Skoda Superb (3T) 07/2008 - 05/2013***
price per Each
incl. tax
Pre-Order
Each
ACV 611320-30-4

ACV 611320-30-4

Item No. 611320-30-4
Facia plate 2-DIN with pocket and HU connector kit i-dapter Skoda / VW Skoda Octavia (1Z) 01/2009 - 03/2013* Skoda Rapid (NH) 10/2012 - 04/2015** Skoda Rapid (NH) 04/2015 - 05/2017** Skoda Rapid (NH) 05/2017 - 02/2019** Skoda Roomster (5J) 06/2010 - 02/2015 Skoda Superb (3T) 07/2008 - 05/2013***
price per Each
incl. tax
Pre-Order
Each

Specifications

Description
ACV 611320-30-4
Category
FULL FITTING KIT SD
Description2
2-DIN Kit with pocket Skoda/VW black 40Pin/52Pin i
CAN Bus
 
 connector: 40 Pin Quadlock VAG
 connector: 52 Pin Quadlock VAG > 40 Pin Quadlock VAG
 connector: OEM SWC > 3,5mm Jack / loose wire
 connector: OEM antenna Fakra(m)(Set) > DIN(m)
 
 blue: +12V antenna remote
 
 activate and configure the rear view camera input in the retrofit HU
  
 connection i-dapter:
 purple/white: +12V reverse gear signal
 RCA(m) ochre: rear view camera input retrofit HU
  
 visualisation i-adapter settings > retrofit HU rear view camera input
 visualisation OPS > retrofit HU rear view camera input
 visualisation Klinatronik > retrofit HU rear view camera input
 
 camera image or i-dapter settings and visualisation not available:
 connect additional GND signal to the RCA outer conductor of the camera and HU connection
  
 vehicles with SWC i-dapter settings:
 press and hold track up SWC buttom
 alternatively with item: 43x-remote
  
 vehicles without SWC i-dapter settings required accessories:
 i-dapter accessories remote control >  interface settings: item: 43x-remote
 
 vehicles with parking assistance front PDC > front PDC is shown after ignition in display
 exit the display > via vehicle PDC switch
 
 +12V reverse gear signal is switched off from 3 km/h
 
 dip switch settings for the retrofit device manufacturer (look into the manual)
  
 vehicles with 40 Pin Quadlock:
 
 vehicles with white OEM MFD instrument cluster
 vehicles with / without OEM amplified system
 
 vehicles VW Caravelle / VW Multivan / VW T5 with OEM amplified system: Active system adapter VW T5/Touareg Quadlock MQS-housing > item: 13-1424-26
 
 vehicles with rear view camera:
 Rear View Camera Interface Seat/Skoda/VW OEM HIGH > item: 771324-1032
 Rear View Camera Interface Seat/Skoda/VW OEM LOW > item: 771324-1036
 
 vehicles Skoda:
 with Audience / Stream OEM HU
 with Amundson / Columbus OEM Sat Nav
 without Technisat OEM HU
 
 vehicles VW
 vehicles with RCD310 / RCD500 / RCD510 OEM HU
 vehicles with RNS315 / RNS510 OEM Sat Nav
 vehicles without RCD320 OEM HU with ISO connector
 
 
 52 Pin Quadlock:
 
 vehicles with MIB-PQ system
 
 check OEM antenna supply voltage with OEM device before installation:
 vehicles with +12V supply voltage OEM antenna
  
 vehicles with 8.5V supply voltage OEM antenna:
 Antenna adapter Fakra(m)(double)>DIN(m) 8.5V > item: 1524-29
 
 connector: OEM rear view camera > RCA(m) ochre
 
 vehicles with/without amplified system
 
 vehicles VW Beetle with Composition Media Dynaudio OEM amplified system supported
 vehicles VW Beetle with Fender OEM amplified system not supported
 
 depending on the vehicle equipment and software:
 not all vehicle settings are supported
 not all vehicle functions are supported
 not all vehicle information is visualised
 
 E-Call not supported
 
 vehicles with E-Call:
 E-Call function retention MAN/Seat/Skoda/VW 52 Pin Quadlock > item: 1424-02
 
 Not for vehicles:
 with OEM Most amplified system
 with open dash
 without any OEM preparation > SWC / speakers / HU
 
 Facia plate:
 
 vehicles Skoda:
 Skoda OEM HU cover required*/**/***/****
 
 1-DIN modular monitor HU > installation with pocket
 2-DIN HU> installation without pocket
 
 2-DIN mounting cutout HU display: 172mm x 98,5mm
 
 Vehicle application:
 
 Skoda
 Skoda Octavia (1Z) 01/2009 - 03/2013*
 Skoda Rapid (NH) 10/2012 - 04/2015**
 Skoda Rapid (NH) 04/2015 - 05/2017**
 Skoda Rapid (NH) 05/2017 - 02/2019**
 Skoda Roomster (5J) 06/2010 - 02/2015
 Skoda Superb (3T) 07/2008 - 05/2013***
 Skoda Superb (3T) 06/2013 - 05/2015***
 Skoda Yeti (5L) 08/2009 - 10/2013****
 Skoda Yeti (5L)  10/2013 - 07/2017****
 
 VW
 VW Caddy IV (DU) 06/2015 - 09/2020
 VW Caravelle (7H) 09/2009 - 05/2015
 VW CC (3C/35) 02/2012 - 08/2016
 VW EOS (1F) 10/2010 - 04/2015
 VW Golf VI (1K) 11/2008 - 09/2012
 VW Golf VI (1KM) 11/2009 - 04/2013
 VW Golf VI Plus (1KP) 03/2009 - 01/2014
 VW Multivan (7H) 09/2009 - 05/2015
 VW Passat B7 (3C/362) 11/2010 - 10/2014
 VW Polo V (6R) 06/2009 - 01/2014
 VW Scirocco III (13) 08/2008 - 04/2014
 VW Sharan II (7N) 08/2010 - 04/2015
 VW Sharan II (7N) 07/2015 - 10/2021
 VW Tiguan I (5N) 06/2011 - 04/2016
 VW Touran I (1T) 08/2010 - 04/2015
 VW T5 Transporter (7H) 09/2009 - 05/2015
 VW T6 (7HC) 07/2015 - 08/2019*****
 
 Colour: piano black
 
 Following signals are provided:
 
 Reimported vehicles or vehicles with different software may be incompatible in functions.
 
 red: +12V ignition clamp 15
 orange: +12V illumination clamp 58
 purple/white: +12V reverse gear signal
 pink: speed pulse signal
 green: GND park brake signal
 
 load capacity outputs: 250 mA max.
 
 current requirement more than 250 mA:
 1 relay coil resistance 75 Ohm min.
 2 relays coil resistance 150 Ohm min.
 
 SWC
 
 visualisation climate control
 visualisation OPS
 OEM amplified system settings
 
 *vehicles with Bolero / Swing OEM HU > Skoda OEM Sat Nav HU cover item number: depending on equipment
 **Skoda OEM HU cover > Skoda OEM item number: 5JA858 415 9B9
 ***vehicles with Amundsen / Columbus OEM Sat Nav
 ***vehicles with Bolero / Swing OEM HU  > Skoda OEM Sat Nav HU cover item number: 3TO8580691QB
 ****Skoda OEM HU cover > Skoda OEM item number: 5L0858069L1 QB
 ***** OEM HU cover must be customised in the middle
 
 Scope of delivery:
 
 2-DIN facia plate with pocket Seat/Skoda/VW black > item: 281320-30-1
 i-dapter Skoda/VW vehicles 40Pin Quadlock Multilead > item: 43xvw01
 Adapter VAG 40Pin Quadlock>52Pin Quadlock MIB bulk > item: 321328-24-0
 Antenna adapter Fakra(m)(set)>DIN(m) 12V phantom LEONI bulk > item: 1524-70-1-0
 
 Optional:
 
 Facia pocket INBAY® for 2-DIN facia plates screw fixing > item: 241000-10-1
 2-DIN facia plate INBAY® Seat/Skoda VW black > item: 241320-30-1
 
 General installation instructions:
 
 Verification:
 1: Check all operating functions and vehicle setting functions of the OEM HU.
 2: Disconnect the OEM HU voltage-free.
 3: Check all interface connections for correctness voltage-free.
 
 Connection and connection sequence:
 1: Check settings and hardware configuration of the interface voltage-free.
 2: Check configuration of the HU connection cable voltage-free.
 3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
 4: Connect all other connections according to the operating instructions of the retrofit HU.
 5: Connect the entire installation to the vehicle with the main connection last.
 6: Software configuration of the interface according to the instructions in the item text and in the manual.
 7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
 8: Function test of steering wheel remote control and vehicle
 
 Changes to the configuration of the interface and the HU connection cable:
 1: Change configuration voltage-free
 2: Reconnection see above 5 to 8
 
 In case of malfunction of the interface or the vehicle:
 1: Reinstall the OEM HU
 2: Operate the OEM HU
 3: Establish CAN bus shut down
 4: Check the hardware configuration of the interface
 5: Reconnection after CAN Bus shut down see above 5 and 6
 
 More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.
 
 More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
 1: Connections and changes are to be carried out exclusively by trained specialist installer.
 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
 3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection.
 4: Connections and modifications are made on the user's own responsibility without guarantee of function.
 5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
 6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.