ACV 611340-08-2

Item No. 611340-08-2
ACV 611340-08-2
Facia plate 2-DIN with pocket and HU connector kit i-dapter Skoda Skoda Octavia (1Z) 2009 - 2013 Skoda Yeti (5L) 2013 - 2017 Colour: black connector: 52 Pin Quadlock VAG connector: OEM SWC > 3,5mm Jack / loose wire connector: OEM antenna Fakra(m)(Set) > DIN(m) connector: OEM rear view camera >
price per Each
incl. tax
Pre-Order
Each
ACV 611340-08-2

ACV 611340-08-2

Item No. 611340-08-2
Facia plate 2-DIN with pocket and HU connector kit i-dapter Skoda Skoda Octavia (1Z) 2009 - 2013 Skoda Yeti (5L) 2013 - 2017 Colour: black connector: 52 Pin Quadlock VAG connector: OEM SWC > 3,5mm Jack / loose wire connector: OEM antenna Fakra(m)(Set) > DIN(m) connector: OEM rear view camera >
price per Each
incl. tax
Pre-Order
Each

Specifications

Description
ACV 611340-08-2
Category
FULL FITTING KIT SD
Description2
2-DIN Kit with pocket Skoda Octavia/Yet 52Pin i-da
CAN Bus
 
 connector: 52 Pin Quadlock VAG
 connector: OEM SWC > 3,5mm Jack / loose wire
 connector: OEM antenna Fakra(m)(Set) > DIN(m)
 connector: OEM rear view camera > RCA(m) ochre
 
 blue: +12V antenna remote
 
 activate and configure the rear view camera input in the retrofit HU
  
 connection i-dapter:
 purple/white: +12V reverse gear signal
 RCA(m) ochre: rear view camera input retrofit HU
  
 visualisation i-adapter settings > retrofit HU rear view camera input
 visualisation OPS > retrofit HU rear view camera input
 visualisation Klinatronik > retrofit HU rear view camera input
 
 camera image or i-dapter settings and visualisation not available:
 connect additional GND signal to the RCA outer conductor of the camera and HU connection
  
 vehicles with SWC i-dapter settings:
 press and hold track up SWC buttom
 alternatively with item: 43x-remote
  
 vehicles without SWC i-dapter settings required accessories:
 i-dapter accessories remote control >  interface settings: item: 43x-remote
 
 vehicles with parking assistance front PDC > front PDC is shown after ignition in display
 exit the display > via vehicle PDC switch
 
 +12V reverse gear signal is switched off from 3 km/h
 
 dip switch settings for the retrofit device manufacturer (look into the manual)
  
 vehicles with MIB-PQ system
 
 check OEM antenna supply voltage with OEM device before installation:
 vehicles with +12V supply voltage OEM antenna
  
 vehicles with 8.5V supply voltage OEM antenna:
 Antenna adapter Fakra(m)(double)>DIN(m) 8.5V > item: 1524-29
 
 vehicles without MOST amplified system
 
 vehicles VW Beetle with Composition Media Dynaudio OEM amplified system supported
 vehicles VW Beetle with Fender OEM amplified system not supported
 
 depending on the vehicle equipment and software:
 not all vehicle settings are supported
 not all vehicle functions are supported
 not all vehicle information is visualised
 
 E-Call not supported
 
 vehicles with E-Call:
 E-Call function retention MAN/Seat/Skoda/VW 52 Pin Quadlock > item: 1424-02
 
 Not for vehicles:
 with OEM Most amplified system
 with open dash
 without any OEM preparation > SWC / speakers / HU
 
 1-DIN modular monitor HU > installation with pocket
 2-DIN HU> installation without pocket
 
 2-DIN mounting cutout HU display: 172mm x 98,5mm
 
 Vehicle application:
 
 Skoda Octavia (1Z) 01/2009 - 03/2013
 Skoda Yeti (5L) 10/2013 - 07/2017
 
 Colour: black
 
 Following signals are provided:
 
 Reimported vehicles or vehicles with different software may be incompatible in functions.
 
 red: +12V ignition clamp 15
 orange: +12V illumination clamp 58
 purple/white: +12V reverse gear signal
 pink: speed pulse signal
 green: GND park brake signal
 
 load capacity outputs: 250 mA max.
 
 current requirement more than 250 mA:
 1 relay coil resistance 75 Ohm min.
 2 relays coil resistance 150 Ohm min.
 
 SWC
 
 visualisation climate control
 visualisation OPS
 
 Scope of delivery:
 
 2-DIN facia plate with pocket Skoda Octavia(1Z)/Yeti(5L) > item: 281340-08-1
 i-dapter Skoda/VW vehicles 52Pin Quadlock Multilead > item: 43xvw03
 Antenna adapter Fakra(m)(set)>DIN(m) 12V phantom LEONI bulk > item: 1524-70-1-0
 
 Optional:
 
 Facia pocket INBAY® for 2-DIN facia plates screw fixing > item: 241000-10-1
 
 General installation instructions:
 
 Verification:
 1: Check all operating functions and vehicle setting functions of the OEM HU.
 2: Disconnect the OEM HU voltage-free.
 3: Check all interface connections for correctness voltage-free.
 
 Connection and connection sequence:
 1: Check settings and hardware configuration of the interface voltage-free.
 2: Check configuration of the HU connection cable voltage-free.
 3: Connect the HU connection cable according to the operating instructions of the retrofit HU.
 4: Connect all other connections according to the operating instructions of the retrofit HU.
 5: Connect the entire installation to the vehicle with the main connection last.
 6: Software configuration of the interface according to the instructions in the item text and in the manual.
 7: Configure the retrofit HU according to the operating instructions of the retrofit device steering wheel remote control/camera/handsfree kit/antenna phantom powering and others.
 8: Function test of steering wheel remote control and vehicle
 
 Changes to the configuration of the interface and the HU connection cable:
 1: Change configuration voltage-free
 2: Reconnection see above 5 to 8
 
 In case of malfunction of the interface or the vehicle:
 1: Reinstall the OEM HU
 2: Operate the OEM HU
 3: Establish CAN bus shut down
 4: Check the hardware configuration of the interface
 5: Reconnection after CAN Bus shut down see above 5 and 6
 
 More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist installer.
 
 More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions:
 1: Connections and changes are to be carried out exclusively by trained specialist installer.
 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications.
 3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection.
 4: Connections and modifications are made on the user's own responsibility without guarantee of function.
 5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface.
 6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.